Welcome to jbperf.com
Sunday, 22 December 2013 at 22:50 EST, by Jean Bélanger
Monday, 2 December 2013 at 14:22 EST, by Jean Bélanger
There is an updated version of the Peak&Hold Injector Driver Board that is used as an external driver box. This is a revised version of the V2.0 board which is now the V2.0.1 version available here. This board has 4 injector drivers and can be used directly with the MS3X injector outputs (among others). For an 8 cylinder engine running sequential injection, 2 kits are needed.
Monday, 2 December 2013 at 14:20 EST, by Jean Bélanger
There hasn't been any update to this news section in a long time. However, there has been a lot of things that have happened in the mean time. I won't list them all because I would certainly miss a lot but hopefully it will be kept current in the future. The forum is always a good place to stay current as everything is announced there.
Saturday, 7 November 2009 at 14:50 EST, by Jean Bélanger
The I/O Extender board is now available. Due to the limited run, I haven't yet put a Paypal button on the web page so you'll have to contact me directly. For more information go to the I/O Extender web page or the forum.
Saturday, 3 October 2009 at 14:34 EDT, by Jean Bélanger
There is now a forum available to discuss anything related to the jbperf.com boards. If you have any question, comment, request, post it on the forum and we can start discussing about it. The forum is here.
Tuesday, 21 April 2009 at 18:36 EDT, by Jean Bélanger
Thursday, 7 March 2009 at 16:55 EST, by Jean Bélanger
The 4-Channel Ignition/Injection Driver Board is available for those using the new MS2/Extra sequential code with the additional injector drivers. Details on the board are available here.
Thursday, 5 March 2009 at 17:02 EST, by Jean Bélanger
The PWM Converter Board, which is for those needing a faster PWM frequency than the ones provided by the current code versions, is available as a complete kit. For more details on the board, have a look here.
Thursday, 10 December 2008 at 17:52 EST, by Jean Bélanger
If you're not into DIY and/or you want or need an external peak&hold injector driver stand-alone box, the 4-driver assembled unit is now available here.
Thursday, 10 July 2008 at 09:51 EDT, by Jean Bélanger
Complete kits are now available for the V1.1 p&h board. You can order, with your board, the components to completely populate the board. Check here for more details.
Monday, 23 June 2008 at 17:47 EDT, by Jean Bélanger
Full kits are now available for the dual VR board. You can order, with your board, the components to assemble one or two of the two available VR conditioner circuits on the board. Check here for more details.
Sunday, 10 February 2008 at 12:00 EST, by Jean Bélanger
Glen's Garage now has the JimStim available as a complete kit and fully assembled. A preview of the V2.0 P&H board is available here. This will not replace the V1.1A board but will be another option for those who want a stand-alone solution in a separate box.
Thursday, 29 November 2007 at 21:27 EST, by Jean Bélanger
The P&H board has been successfully installed on a VEMS ECU. For more details have a look at Sprocket's wiki. This could also open the door for the use of the P&H board with the v3.57 board.
Friday, 16 November 2007 at 23:41 EST, by Jean Bélanger
Here's a preview of the Wheel Translator board.
Thursday, 18 October 2007 at 13:30 EDT, by Jean Bélanger
The Peak&Hold Board V1.1A is now available. The V1.1A board is essentially the same board as the V1.1 board but has 4 mounting holes to allow different options for board installation. It has the same features and components as the V1.1 board.
Friday, 12 October 2007 at 19:54 EDT, by Jean Bélanger
DIYAutoTune has added the assembled JimStim to their products.
Tuesday, 25 September 2007 at 16:34 EDT, by Jean Bélanger
The JimStim is now available as a complete kit from DIYAutotune. Click here for more details. I will continue to have the partial kit available for those who prefer it and those who want to buy it together with another one of my boards.
Saturday, 11 August 2007 at 20:50 EDT, by Jean Bélanger
This is a quick attempt at regrouping all the information about the boards I offer. It is still very much in construction. It basically just regroups the information I already had into a single more easily navigated site. I will update the site as time allows.
Peak&Hold Injector Driver Board
This is a small board that fits into the last slot of the top half of the standard MegaSquirt enlosure. It can drive up to 4 low-impedance injectors.
Signal Interceptor Board (breakout board)
This board allows all the signals coming into and out of the MegaSquirt to be analyzed and/or interrupted. this board can be used either while bench testing or on a running engine for installation diagnostics.
JimStim - The Megasquirt Stim with a Wheel Simulator
This is a new version of the stimulator originally designed by James Murray (jsmcortina on the forums) that expands on the original stim's features. The main improvement comes with the addition of a microcontroller which allows the simulation of up to 30 different toothed wheels in addition to the standard distributor signal of the old stim. At the moment, there are 23 programmed wheel patterns but the firmware is upgradable using a specific USB cable made by FTDI (see BOM).
Dual VR Conditioners Board
This is a small board (with the same footprint as the p&h board) that fits into the last slot of either half of the standard MegaSquirt enlosure. It has 2 VR conditioner circuits using LM1815s and 4 ADC conditioner circuits.
PWM Converter Board
This small board is for those needing a faster PWM frequency for their FIDLE or boost controller than the ones provided by the current code versions. It has a CPU which reads the original PWM signal and generates a new PWM signal with the same duty cycle and precision but with a higher frequency. The new frequency can 2, 4, 8, 16, 32, 64, 128, or 256 time faster than the original signal.
4-Channel Ignition/Injection Driver Board
This board combines 4 injector drivers, 4 ignition drivers, and one DB15 connector to clean up the wiring inside of the MegaSquirt case when using additional injector drivers with the new MS2/Extra sequential code. It can also be used for the ignition drivers and connector with any other MS2/Extra code version. It has the advantage of isolating all the high current devices from the main MS board and therefore reducing electrical noise to a minimum.